x870e motherboard ASUS ProArt X870E-CREATOR WIFI - Ryzen 9950x

[fabiosun]

could you connect both monitor on rx 6600 (leaving your 4090 inside)?

 

and press space before launching your USB pen icon (then reset Nvram)

[khile]

10 minutes ago, fabiosun said:

could you connect both monitor on rx 6600 (leaving your 4090 inside)?

 

and press space before launching your USB pen icon (then reset Nvram)

We have progress!

It hangs here, but we are moving forward 

 

Thank you for all help so far

[fabiosun]

config 2.plist.zip

press space bar reset nvram

then try again

[khile]

13 minutes ago, fabiosun said:

config 2.plist.zip 7.16 kB · 1 download

press space bar reset nvram

then try again

Its working!!!!

Can boot all the way into recovery but then complains there is no internet connection but i can at least get there now thank you so much

[fabiosun]

ohhhhh

ok we can try to enable your aquantia or the other one

 

[khile]

Just now, fabiosun said:

ohhhhh

ok we can try to enable your aquantia or the other one

 

So I run the 10G LAN (Marvell) as  i have 5gb fibre

Honestly thank you so much for all your help 

[fabiosun]

you should try with both lan you have but we have to modify your config

if you like to try i will do for you

let me know

 

[khile]

1 minute ago, fabiosun said:

you should try with both lan you have but we have to modify your config

if you like to try i will do for you

let me know

 

If you don't mind, that would be greatly appreciated 

[fabiosun]

config.plist.zip

using aquantia

 

Archive.zip

using intel ones

 

copy the kext in your /oc/kext folder

try both separately (both config posted)

Edited 2 hours ago by fabiosun

[khile]

So using the 10g now and it’s working 

 

installing now 

[fabiosun]

let see if it instal then we have to see if your gpu is accelerated and audio part 🙂

happy for you

 

also for me because i thought i lost my touch (in hackintosh ) 🙂

 

[khile]

So it seems to be stuck at AppleKeyStore:pid94,:13108 operation failed (sel: 7 ret: e00002f0, -1)

 

it installed find this was after it rebooted 

 

rebooted again and now stuck at

Edited 1 hour ago by khile

[fabiosun]

did you wait a bit and always stuck there?

if so you can try to disable -v in your boot arg and see if it works

 

config.plist.zip

[khile]

It’s seems to vary where it stops I’m reinstalling just in case something went wrong and then if not I will try the above file and report back 

 

thank you 

 

edit:

 

now gets stuck here constantly 

Edited 1 hour ago by khile
Added photo

[fabiosun]

try config plist put above 

 

[khile]

So using the above file the bar gets around 1/3 of the way and then the computer restarts 

[fabiosun]

you should not see verbose output

do for a couple of time

 

[khile]

So it’s now showing but only on 4090 the 6600 remains no signal 

 

I’ve gone though account creation and now stuck on a gray screen 

[fabiosun]

probably we should find pci address for rx slot and build a bridge for it with ssdtime 

 

if you do not do damage i would for only try to remove your 4090 and use rx 6600 on first gpu slot near CPU

or try to enable whatevergreen kext if disabled or enabled it...

 

now all is good and the only variable are your beast unsupported installed on system (i dont know how to disable it correctly in OSX)

other variable is PCI bridge for your slot