Jump to content

[AMD] Clover Vanilla patches

fabiosun

By fabiosun
in General

 Share

Recommended Posts

Recommended

Posted by fabiosun,

With the publication of the updated kernel patches, now available for everyone, it is possible to clean up the thread, also thanks to the patch present in the PR published by Shaneee in the Opencore github, also applicable to Clover.   So I'll clean up some of my posts by referencing this post (UPDATED 18-07-2021)   AMD OSX Patches   Shaneee Pull Request   I provide quirks and patches useful for my system (and as regards the kernel patches also for di

Updated 19-07-2021

Recommended by fabiosun

  • Like

1 reaction

Go to this post
  • 2 months later...
jsl2000 Senior Member

jsl2000

Posted
Posted (edited)
On 7/31/2021 at 12:43 PM, fabiosun said:

also about this

if you read well

only few users need of this patch.

newer one has a problem with clover masking system , and you can also see in AMD OSX Github why they left Clover without an official patches support..

Then is it possible to have it working well..and we have this from months

 

Hi, fabiosun:

I need your help to fix my Ryzen 1700X's Clover 5140.1 config.plist which can boot 10.13.6/10.14.6/10.15.7/12.0beta9, but always got freeze after +++++++++++++ for Big Sur 11.5.2 or 11.6.1.

Using old config-working-Ryzen-5138.plist which can boot Big Sur, but always got hang after running for 1~2 minutes.

No such an issue by OpenCore 0.7.2 or 0.7.4 with similar kernel patches.

config.plist.zip config-working-Ryzen-5138.plist.zip

Edited by jsl2000
Link to comment
Share on other sites
  • Supervisor
fabiosun Senior Member

fabiosun

Posted
  • Author
  • Supervisor
Posted

@jsl2000clover dev is trying to port new feature to install correctly new Montereys beta, I will wait they finish their work

for now is a bit confused in my opinion

 

I am using latest clover as my second bootloader and I have no problem on BS 11.6.1 and on MR beta 10 (installed with Opencore I mean for beta 10)

 

Your working config is a bit...very confusing me

you beat record of used patches there 🙂

You mix new patches with old patches..I have to read it better to understand

Have you a working clover config for 1700x for all OSX you need?

without freeze I mean

 

Link to comment
Share on other sites
jsl2000 Senior Member

jsl2000

Posted
Posted (edited)
1 hour ago, fabiosun said:

for problem on old (and bad one for patches imho) config.plist...try to enable Dummypowermanagement quirk

I attached also here my working kernel patches for BS 11.6.1 and MR beta 10

 

clover patches.plist.zip 1.88 kB · 1 download

 

maybe you have to add here only topology patch and Fix pat you use

Thanks for your kind and prompt reply and help.

Unfortunately this config.plist can boot both Big Sur and Monterey past +++++++++++++, but unable to login desktop successfully.

I need figure out how to fix it or using my old config.plist temporarily because I can boot Ryzen and FX-6300 with old patches by OpenCore and Clover. The only disvantage is ProvideCurrentCpuInfo must be disabled to avoid red screen panic during booting.

Edited by jsl2000
  • +1 1
Link to comment
Share on other sites
  • Supervisor
fabiosun Senior Member

fabiosun

Posted
  • Author
  • Supervisor
Posted
2 hours ago, jsl2000 said:

Using old config-working-Ryzen-5138.plist which can boot Big Sur, but always got hang after running for 1~2 minutes.

for this instead I mean you have to add Dummypowermanagement quirk in that config.plist

(should be mandatory for you also in opencore booloader)

Link to comment
Share on other sites
  • 3 months later...
SavageAUS Member

SavageAUS

Posted
Posted (edited)
3 hours ago, fabiosun said:

@tomnic12.3 has so much problems and also 2 d performance is a pain

 

@SavageAUS

maybe the lack of performance in this beta helps clover

 

no interest from clover dev and patches devs to understand  tsc problem

I’ll give it a try after and report back. Hopefully we can convince Slice to look into adding the quirk needed to Clover. 

On Monterey 12.2 21D49 with Clover 5144 issue still exists.

Clover Left OpenCore Right

Clover 5144.png126185069_OpenCore0.7.7.png.e0ef0adeb82261fae31f84b46c5204ea.png

Edited by SavageAUS
  • Cross Finger 2
Link to comment
Share on other sites
  • Supervisor
fabiosun Senior Member

fabiosun

Posted
  • Author
  • Supervisor
Posted

@SavageAUSyou have some hope in latest 12.3 beta 1

But it is not usable well also with opencore for many problems it has

But clover seems to work here ( no speedy animation and also no wifi disconnect) 

Bad GPU performances

Clover Geekbench metal about 59000

Opencore Geekbench metal about 102000

in a working OS I have here about 202000! 

  • Sad 1
Link to comment
Share on other sites
  • Supervisor
fabiosun Senior Member

fabiosun

Posted
  • Author
  • Supervisor
Posted

I have an idea that until the clover conversion is fully done we won't have a safe clover to use
TSC-level patches work with clover in a different way
and this from before we noticed the problems with monterey 12.1 and 2
Now by Miracle, with the new beta that works horribly even with Opencore
Clover has started working again, clearly the problem is not only Clover but also (maybe) the old patches that we have to use with clover due to the lack of the famous quirk

 

 

Link to comment
Share on other sites
SavageAUS Member

SavageAUS

Posted
Posted
2 minutes ago, fabiosun said:

433703855_Screenshot2022-01-29at9_56_34AM.thumb.png.e20185ecd7b46e8abf712b231a31bfa3.png

R5144 and 12.3 beta1

12.2 here does not start (black screen on gpu)

Some times starts..but double speed animation and WIFI disconnection

Obviusly same config.plist

 

5132 was doing that as well. If I try start verbose I get black screen, without verbose boots fine but double speed animations and wifi plays up. 

Link to comment
Share on other sites
SavageAUS Member

SavageAUS

Posted
Posted (edited)

I’ve updated to 12.3 beta 1 and both OpenCore and Clover are working ok. Clovers fast animations and wifi problem are gone. Google Chrome no longer opens though. 
Geekbench 5 Clover Metal 63141. 

Gewkbench 5 OpenCore Metal 68669. 

Edited by SavageAUS
  • +1 1
Link to comment
Share on other sites
SavageAUS Member

SavageAUS

Posted
Posted (edited)
14 minutes ago, fabiosun said:

config.plist.zip 4.87 kB · 1 download

 

try this

I have disabled patches:

3)

11)

12)

 

backup first yours

 

So far so good.

 

Frequencies are still different than OpenCores though.

OpenCore left Clover 5144 with new quirk on the right.

418046589_OpenCore0.7.7.png.926ccd72043a2d8f63a7c3ee05918798.png181706103_Clover5144NewQuirk.png.022b4e8f2fe644e5f701abf808506f79.png

293361694_ScreenShot2022-01-29at10_54_43pm.thumb.png.902ece5c7b85a794aa21ffbf8325d5f4.png 1885010263_ScreenShot2022-01-29at10_55_15pm.png.61babfcf7957c6d6ba557375b4cfa891.png

 

I will continue to test via USB boot until I am happy 🙂

I am just glad we were able to get Clover back on AMD working....mostly.

 

Google Chrome and GitHub Desktop applications are currently not working.

Edited by SavageAUS
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing
×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.